Wilbur-curtis EXPR Manual do Utilizador descarregar pdf (Página 1)

NSF International requires the following water connection:

1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) is required so

that the unit can be moved for cleaning.

2. Thisunitmustbeinstalledwithadequatebackowprotectiontocomplywithapplicablefederal,

state and local codes.

3.Waterpipeconnectionsandxturesdirectlyconnectedtoaportablewatersupplyshallbesized,

installedandmaintainedinaccordancewithfederal,state,andlocalcodes.

Symbols

WARNINGS – To help avoid personal injury

Important Notes/Cautions – from the factory

Sanitation Requirements

Service Manual – Expressions Multi-avor

This Curtis Generation 3 Unit is Factory Pre-Set and Ready to Go Right from the Box.

Following are the Factory Settings for your Expressions Multi-avor Beverage System:

• Tank Temperature = 190°F

• Dispensing Mode Set for Manual Dispense

Generally there will never be a reason to change your G3 programming. However, should you need

to make slight adjustments to meet your dispensing needs, programming instructions are provided

later in this manual.

System Requirements:

• Water Source 20 – 90 PSI (Minimum Flow Rate of 1 GPM)

• Electrical: See attached schematic for standard model or visit www.wilburcurtis.com for

your model.

Wilbur Curtis Company, inC.

Important Safeguards/Symbols

CAUTION: DO NOT

connect this unit to

hot water. Inlet valve

not rated for hot water.

CAUTION: Use this

setup procedure

before attempting

to use this appliance. Failure

to follow the instructions can

result in injury or the voiding

of the warranty.

WARNING HOT

LIQUID, Scalding

may occur. Avoid

splashing.

Model Included:

■ EXPR

ISO 9001:2008 REGISTERED

WILBUR CURTIS CO.

Montebello,CA90640

For the latest information go to

www.wilburcurtis.com

Tel:800/421-6150

This equipment is designed for commercial use. Any servicing other than cleaning and routine

maintenance should be performed by an authorized Wilbur Curtis Company Service Technician.

• DO NOT immerse the unit in water or any other liquid

• To reduce the risk of re or electric shock, DO NOT open service panels. There are no

user serviceable parts inside.

• Keep hands and other items away from hot areas of the unit during operation.

• Never clean with scouring powders or harsh chemicals.

3. Connect the unit to electrical outlet with appropriate amperage rating (see serial tag on machine).

4. Once power has been supplied to the unit, ip the toggle switch to the ‘ON’ position (located on the rear of

the unit), the water tank will begin to ll. When the water level in the tank reaches the probe, the heating

element(s) will turn on.

5. Water in the heating tank will require approximately one hour before reaching operating temperature (factory

setting of 190°F). Where applicable, turn on the Universal Control Module (UCM). When the unit reaches

operating temperature, it will display “READY TO BREW”.

NOTE:Awaterltrationsystemmustbeusedtohelpmaintaintrouble-freeoperation.Air must be purged

from the cartridge prior to connection to equipment. Inareaswithextremelyhardwater,wehighly

recommendtheuseofaCurtisapprovedwaterlter.Forourfulllineoflters,pleaselogontowww.wilbur-

curtis.com.

SETUP STEPS

1. The unit should be level (left to right - front to back), on a secure surface.

2. Connect the water line to the water inlet tting on the rear of the unit. Water volume ow to the machine

should be consistent. Use tubing sized sufciently to provide a minimum ow rate of one gallon per minute.

1 2 3 4 5 6 7 8 9 10

Resumo do Conteúdo

Página 1 - Wilbur Curtis Company, inC

1NSF International requires the following water connection:1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) is r

Página 2 - Operation Instructions

10ECN16005.7/10/[email protected].revEECN15517.12/16/[email protected].revDECN14425.9/18/[email protected]10304.2/26/09@14.8WILBUR CURTIS CO., INC.6913AccoSt.

Página 3 - Steps to Programming

2Fill Canisters Daily1. Open the front door to access canisters.2. Rotate the powder delivery elbows upward. 3. The canisters must be removed from the

Página 4 - Program Menus

3 a. Take hold of the whipper chamber with one hand while holding the whipper mounting plate with the other. Turn it clock wise to free it

Página 5

4Program Menus Manual Dispense (Factory Default)Press  or ► to go to Manual Dispense Select. Press  to go to Manual Dispense Select Station.Choose t

Página 6 - Illustrated Parts – Main View

5Conguration of Canisters MODELONE10 LB. CANISTERP/N CA-1113-06RULTRA-SLIMP/N CA-1142-07FOUREXPRABCDEBefore mounting a whipper plate, place a dab of

Página 7 - Illustrated Parts – Chassis

6125634Illustrated Parts – Main ViewCOVER, TOPPANEL, LEFT SIDE EXPRBRACE, LEFT SIDEDOOR, COMPLETEBRACE, RIGHT SIDEPANEL, SIDE RIGHTLAMP, 30W 5K CIRCUL

Página 8

7789103132333735363438394043441313A1615141713B2019182122232427282930111246252628A56Illustrated Parts – ChassisSTEAM TRAPCONNECTOR, ORIFICE WATER PCGTB

Página 9 - Electrical Diagram

8505152535455474948454142Illustrated Parts – Heating Tank363738394041424344454647484950515253545556WC-826L *WC-58229WC-8591 *WC-796 *WC-3518WC-5231 *W

Página 10 - Product Warranty Information

9TANKWATERElectrical Diagram

Comentários a estes Manuais

Sem comentários

Wilbur-curtis EXPR Manual do Utilizador Página 1

Consulte online ou descarregue Manual do Utilizador para Máquinas de café Wilbur-curtis EXPR. Wilbur Curtis EXPR User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Wilbur-curtis EXPR Manual do Utilizador Página 1

Consulte online ou descarregue Manual do Utilizador para Máquinas de café Wilbur-curtis EXPR. Wilbur Curtis EXPR User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Máquinas de café Wilbur-curtis EXPR